Need laser equipment advice? Our team is ready to help. Get a Free Quote

My 7-Step xTool S1 Cleaning Checklist (And What Skipping It Actually Costs)

Who this checklist is for (and why I finally wrote it down)

I'm the procurement lead at an 8-person custom signage shop. I've managed our equipment and consumables budget (roughly $30,000 a year) for three years, negotiated with more than 10 vendors, and logged every replacement part in a cost spreadsheet that, honestly, has paid for itself twice over.

This is the cleaning checklist I use on our xTool S1 machines. Seven steps, about 35 minutes end to end. It's built for the small shop owner, the side-business operator, or the one person in the company who got handed the maintenance calendar along with everything else on their plate.

I'll be blunt about why I wrote this down. Two years ago, I didn't have a checklist. I had "clean it when it looks dirty." That worked fine until one of our laser modules started losing focus on wood, then on acrylic, and then stopped marking metal cleanly. The replacement quote is still taped to my monitor. The reason it stings isn't the number — it's that I couldn't tell you which of the seven things I'd skipped led to it. From the outside, laser maintenance looks like a rag and five minutes. The reality is closer to a consumables-tracking exercise — the wipe is the easy part, and knowing when to do it is the actual cost control.

Two anchors before we start. ANSI Z136.1 is the U.S. safety standard for laser use, and FDA CDRH governs the certification and labeling of laser products. Two practical rules flow out of both: wear protective eyewear any time the enclosure is open, and never break the airflow path before you kill the smoke source. On the S1, that means letting the fan spin down before you open the work area — not the other way around.

The seven-step checklist

Step 1: Power down and cool the module

Turn the machine off, unplug the power, and let the laser module cool for at least 10 minutes. I usually give it 15, because I've burned a fingertip on a 20W module before (note to self: put the "do not touch" sticker back on the bezel).

Why this step runs first rather than last: everything below it involves reaching inside the machine. You don't want to reach in while the module is hot, or while a stray command could still fire the laser.

Checkpoint: Plug is out, fan is quiet, module is cool to a gloved hand.

Step 2: Clean the laser module lens (the one most people skip)

This is the step that gets skipped, and it's the one that costs the most when it does. The lens looks clean when you hold it up. It always looks clean. Under a headlamp, tilted at a low angle, you'll see a faint oil film starting to form after roughly six hours of wood engraving. That film absorbs power, turns into a hot spot, chips the coating, and kills the module. None of that happens on a date you can see on a calendar.

Here's the routine:

  • Pull the module per the manufacturer's instructions. xTool's manual specifies which screw, which direction — follow it, not whatever YouTube video you found at 11 p.m.
  • Wipe the protective lens with a lint-free cloth and a drop of 90%+ isopropyl alcohol. Not paper towels. Not your shirt.
  • Re-inspect under angled light before you reinstall.
  • Log the date and the hours currently on the module in your maintenance sheet.

The lens on the S1's interchangeable modules — 10W, 20W, or 40W, depending on which you're running — is replaceable separately from the module itself. That's the only reason this step is cheap. If you wait until you can see damage, you've moved from a five-dollar wipe to a several-hundred-dollar module swap.

Checkpoint: No visible film under angled light, no scratches, module reinstalled with screws snug (don't over-torque these — the housing thread is fine-pitch).

Step 3: Clear the honeycomb bed and debris tray

Every two weeks if you're cutting wood. Every week if you're cutting acrylic or leather. Empty the tray, brush the honeycomb with a soft brush, and — the part I missed for the first year — wipe down the tray gasket with a dry cloth. Resin from acrylic off-gassing collects there and hardens into something you'll need a chisel to remove.

It's tempting to think a clogged bed is just a "housekeeping" problem. But a bed that's no longer flat will produce inconsistent acrylic edges, and the first person to notice usually blames the settings. It almost never is the settings. It's the bed.

Checkpoint: Tray is empty, honeycomb has no visible resin beads, gasket is dry to the touch.

Step 4: Check the exhaust fan and filter

The filter is where TCO thinking on a laser actually matters. Replace it on a time interval, not on a symptom — most small shops are looking at somewhere in the 40–60 hour range depending on material. If you wait for the "I can smell it" moment, you've already been running too long.

On the S1, this is also the step where you catch airflow issues before they become burned-out fans. Once a month, unplugged, spin the fan by hand. It should spin freely and coast for a beat. If it stops dead, the bearings are going, and a fan replacement now is cheaper than a module replacement later.

Keep every filter and fan receipt. Your quarterly cost review is going to want it, and "I think it was around $120" is not a line item your accountant enjoys. If I remember correctly, my first-year filter spend came in at roughly $340 — though I might be misremembering the exact number, and I'm not going back through 14 months of receipts to double-check.

Checkpoint: Filter change date logged, fan spins freely by hand, no obvious smoke staining on the blades.

Step 5: Inspect belts and rails

Wipe the rails with a dry cloth. Check belt tension — about half an inch of deflection under light finger pressure is a reasonable reference, though I've never measured mine precisely and probably shouldn't pretend otherwise. If a belt feels noticeably looser than when you installed it, it's stretching, and that shows up later as shifted cuts on the far end of the bed.

Two cautions here. First, don't tighten a belt without reading the manual's tension spec — over-tight belts wear out the steppers faster than loose ones do. I learned that one in 2023 when I tightened a belt "just to be safe" and burned through a stepper in four months. Second, if your S1 sits on a mobile cart (mine does), check the cart's leveling feet while you're down there. I once spent a whole afternoon chasing a "misaligned" laser that turned out to be a cart on a sloped floor.

Checkpoint: Rails clean, belt deflection roughly even on both sides, cart level.

Step 6: Run a calibration test with a free engraving file

This is the step that makes the other six worth doing. Once you've cleaned and reassembled, run a test pattern before you trust the machine with a paid job.

I keep a folder of free laser engraving files — the xTool project library plus a few community sources — and once a month I run the same small square: one mark on scrap wood, one on scrap acrylic, one on scrap anodized aluminum. I compare it to the prior month under a loupe. Faded metal mark? Lens. Yellowed acrylic edge? Exhaust. Doubled edge on wood? Belt.

Two materials are worth keeping in the rotation even if you don't sell them: laser marking glass and laser marking anodized metal. They're my most sensitive indicators for lens condition and focus calibration. A clean mark on glass tells me the focus is right within a fraction of a millimeter, which is exactly what I want to know before a long production run on a laser marking machine for metal. Five minutes of verification beats five days of correction — I've watched a whole batch of 40 acrylic awards get re-cut because someone skipped the test square.

Checkpoint: Test mark matches the prior month, no fading, no doubling, no yellowing.

Step 7: Log the maintenance and update your cost tracker

The most skipped step of all, and the one that closes the loop. I log four things every session: date, hours on the module, what I cleaned, and what I replaced. At the end of each quarter, I total it against the machine's annualized cost and look at one number: cost per hour of runtime.

That number is what converted my cleaning habit from a chore into a strategy. Recorded in my cost tracker, mine sat at roughly $4.80 per runtime hour when I started in 2023. After 14 months of consistent preventive maintenance, it's dropped to about $3.10. Same machine, same materials, fewer surprise replacements. That's roughly a 35% drop in operating cost, and I didn't change anything about the work I run through the machine.

Checkpoint: Maintenance log updated, cost per hour recalculated for the quarter.

Common mistakes (and the ones I actually made)

I'll close with the errors I actually made, not the ones I read about online.

  • Wiping the lens with paper towel. It sheds lint that looks like a scratch, and lint catches fire. Lint-free cloth only.
  • Skipping the filter change because it looked fine. The filter's whole job is invisible. "Looks fine" means nothing.
  • Tightening the belt "for safety." Cost me a stepper in 2023. The belt was fine. I was not.
  • Cleaning on a calendar instead of on runtime hours. Hour-based cleaning is far more accurate. If I ran 15 hours of acrylic this week, I clean. If I ran two, I wait.
  • Ignoring the smell. If your shop smells like burning wood 20 minutes after the machine is off, your exhaust path has a leak. Don't "keep an eye on it." Fix it before the next job.

Two honest caveats

First, this checklist was accurate as of January 2025. xTool updates the S1's consumable specs and filter intervals periodically, so verify the current replacement intervals against the official product specs before you place your next order.

Second, my experience is based on two S1 machines and roughly 1,400 material test pieces, mostly in a small signage shop doing mixed wood, acrylic, and anodized metal. If you're running heavy production loads, or cutting thick acrylic all day, your wear curve will look different — shorter on filters, probably longer on belts.

The point of this list isn't to follow it perfectly. It's to catch small problems while they're still small. The five-dollar lens wipe versus the several-hundred-dollar module isn't a figure of speech. It's the actual arithmetic I run every time I think about skipping step 2.

author-avatar
Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply